Catalyst for two-components oil One coat 2k wood oil in a ratio of 100: 30.

Water-based primer for the pretreatment of wooden surfaces. It is ideal as a first basic treatment especially on woods with a high tannin content. Its characteristics allow an excellent adhesion on the wood making it an ideal base to prevent yellowing and the appearance of dark spots on the surface, especially in the case of water-based finishing cycles in light colors

3-in-1 oil-wax based exterior self sealing finish: a single product that impregnates, protects and decorates. It is applied in two or three coats on rough wood. It does not need intermediate sanding. It is maintained with a simple overlay. Suitable for ceilings, beams, external wood cladding, fixtures, fences, pergolas, etc.

External wood basecoat, for grainy and brittle wooden surfaces. It masks inhomogeneity and restores a clear and luminous color. Sealing and consolidating, it prepares the surface for finishing, usually withHolzwachs lasur 3in1.

Iron-micaceous enamel is a ready-to-use product, easy to apply, special for metal, indoors and outdoors, with exceptional anticorrosive and decorative properties. Creates a water-repellent and weather-resistant film, with a pleasantly antique look. Thanks to the special formulation with medium-fine grain micaceous iron oxides, it guarantees excellent coverage and long-term protection. Smooth and elastic, it is characterized by an excellent distension and does not drip. strong> p>

Fields of use:
It is recommended for the finishing or maintenance of iron surfaces, with or without the use of Anti-rust Undercoat (code 6915) or a high coverage Undercoat (code 6910).
It can also be applied on wood to obtain an effect similar to that of wrought iron.
Ideal for gates, railings, fixtures and metal elements in general. p>

A waterbased acrylic, waxy impregnating self-sealing 3-in-1 finish for interiors and exteriors.
Odourless and dilutable in water it enhances the grain of the wood using natural and bright colours for deep penetration of the wood.
Water repellent and breathable it protects the wood from atmospheric agents. Added UV filters impart light-stability and special additives protect the wood against harmful biological agents. Application of two or three coats is recommended. Recommendations for application:
The colours of Naturaqua Holzwachs Lasur 3IN1 are brighter than the same Holzwachs Lasur 3IN1 oil-wax base.
The level of protection offered by the two products is very similar, however the water-based version needs intermediate sanding between the coats and restoration phase.

Water based detergent to restore wood to its natural color. It removes the gray patina caused by the decomposition of lignin under the action of ultraviolet radiation.
Apply on the wet surface, leave for 5 minutes, then clean the wood with a stiff brush. Rinse with water after application. Ideal for coverings, garden furniture, fences, decking.
Massage the surface with a brush or brush until the surface is still wet. The result is immediate.
If necessary, repeat the operation.

Wax-effect finish for interior and exterior. Enhances the structure of the wood. Water repellent and breathable, it protects the wood from atmospheric agents, also thanks to UV filters. Contains additives to protect wood from harmful biological agents.
Application in two coats is recommended.
For greater resistance of the coating, apply Holz Lasur as a first coat.
Suitable for ceilings, beams, external cladding, wooden houses, pergolas, fences, etc.

Two-component one-coat oil for the finishing of all wooden surfaces both indoors and outdoors. Mix of natural oils, zero emissions, 100% solid content, to be cured at 30%. Easy to apply (manual or with single-brush), it allows to treat all surfaces both indoors and outdoors with excellent levels of protection. To be used in combination with the relatedcatalizzatore in rapporto 100:30.

It allows intensive cleaning of the wood, removing stubborn dirt and residues of previous oil-based or impregnating treatments. It is also used to degrease exotic timbers particularly rich in oils and extracts. In this case it is recommended to dilute the product with water 1: 1. Wet the substrate with plenty of water before treatment. Due to the high concentration of active ingredients, Extra Strong Wood Cleaner can alter the natural color of the wood making it darker. To restore the original color of the wood, use Exterior Wood Cleaner later.